Rolling and Plain Bearings

Approx. Rs 500 / Piece(s)Get Latest Price

Approx. Rs 550 / Piece(s)Get Latest Price

Series BXRE:

• High load rating, dimensions in accordance with DIN 625-1
• Long rating life
• Downsizing possible

Approx. Rs 500 / Piece(s)Get Latest Price

Special Series: Wheel Bearings:

• High performance density – less space
• High axial and radial load carrying capacity
• High moment support

Energy Efficiency Class A in Vehicles: Wheel Bearings with Reduced Weight and Friction:

Lower mass and less friction mean lower fuel consumption, improved energy efficiency and an enhanced environmental performance evaluation. Good reasons to keep our new INA ball roller bearings in mind.

Approx. Rs 2,500 / PieceGet Latest Price

Tapered roller bearings comprise solid inner and outer rings with tapered raceways and tapered rollers with cages. The bearings are not self-retaining. As a result, the inner ring together with the rollers and cage can be fitted separately from the outer ring. Tapered roller bearings can support axial loads from one direction as well as high radial loads. They must normally be axially adjusted against a second bearing fitted in a mirror image arrangement.

X-life

We are offering our proven catalog series in X-life quality. The geometry, surfaces and materials were optimized. Thus FAG Tapered Roller Bearings X-life offer an increase in the basic dynamic load ratings (Cr) of up to 20 % compared to previous designs, an increase in the basic rating life of approximately 70 % under the same operating conditions und up to 75 % less friction. A convincing advantage of X-life are product characteristics that provide you with new design perspectives, for example, to design particularly low-noise or high load capacity systems solutions.

Approx. Rs 100 / Piece(s)Get Latest Price

Drawn cup roller clutches are one-way clutches comprising thin-walled, drawn outer rings with a series of ramps on the inside diameter, plastic cages, springs and needle rollers. They can transmit torques in one direction and are radially compact. The roller clutches are available with and without a bearing assembly.

Drawn cup roller clutches give very precise indexing, since individual spring retention of each needle roller ensures constant contact between the shaft, needle rollers and the clamping surfaces. They allow high indexing frequencies due to their low mass and therefore the low moment of inertia of the clamping elements. They also have a low free-wheeling frictional torque.

Drawn cup roller clutches can be used in a wide variety of applications, for example as indexing elements, back-stopping clutches or overrunning clutches. The drawn cup roller clutch fulfils the overrunning or holding function as appropriate.

Approx. Rs 150 / Piece(s)Get Latest Price

Thin section bearings have high precision, are very quiet and have high load carrying capacity. These ball bearings are available in three different designs and have an extremely small, predominantly square cross-section. Within each series, the cross-section remains constant even for larger shaft diameters and housing bores. The bearings are therefore also described as Constant Section (CS). This special feature distinguishes thin section bearings from conventional bearings as standardized in ISO series.

It is therefore possible to select a larger cross-section and thus use a bearing with higher load carrying capacity without the need to change the shaft diameter as well. Thin section bearings allow designs to be achieved that are extremely light and require little space.

Deep groove ball bearings, four point contact bearings, angular contact ball bearings

Thin section bearings are available as deep groove ball bearings (C), four point contact bearings (X) and angular contact ball bearings (E). Each of these designs is available in various series. The series correspond to the cross-section sizes. The balls are matched to the series.

Deep groove ball bearings can support axial loads from both directions as well as radial loads.

Four point contact bearings can support axial loads from both directions as well as radial loads; they thus act in the same way as double row angular contact ball bearings.

Angular contact ball bearings can be filled with an optimised number of balls and have a contact angle of 30°. They can support considerably higher radial loads than deep groove ball bearings or four point contact bearings are can support axial loads from one direction. For special requirements, angular contact ball bearings are also available as matched bearings. These combinations then have a significantly higher rigidity and load carrying capacity than single bearing solutions.

Approx. Rs 1,150 / Piece(s)Get Latest Price

Needle roller and cage assemblies are single or double row units comprising cages and needle rollers.
Since their radial section is no greater than the diameter of the needle rollers, needle roller and cage assemblies allow bearing arrangements with a very small radial design envelope to be achieved. They have very high load carrying capacity, are suitable for high speeds and can be easily fitted.

If the raceways are produced to high geometrical accuracy, bearing arrangements with high runout accuracy can be achieved.

The radial internal clearance can be influenced by the needle roller sort and by the shaft and housing tolerance.

Needle roller and cage assemblies require a hardened and ground raceway on the shaft and in the housing.

Approx. Rs 250 / Piece(s)Get Latest Price

Approx. Rs 400 / PieceGet Latest Price

Axial spherical roller bearings are single row, self-aligning roller bearings. They comprise solid shaft and housing washers and asymmetrical barrel rollers with cages. The cage holds the roller and cage assembly together with the shaft locating washer. The bearings can be dismantled. The parts of the bearings can be fitted separately.

Axial spherical roller bearings can support very high axial loads and permit relatively high speeds. Both under the harshest of operating conditions. For example in gearboxes, calenders, engines in marine applications and rudder engines, lifting gear, construction machinery and rolling mills.

Approx. Rs 300 / PieceGet Latest Price

Approx. Rs 500 / PieceGet Latest Price

Spherical roller bearings are double row, self-retaining units comprising solid outer rings with a concave raceway, solid inner rings and barrel rollers with cages. The inner rings with cylindrical or tapered bores.

The symmetrical barrel rollers freely align themselves to the concave outer ring raceway. As a result, shaft deflections and mislignments of the bearing seats are compensated.

X-life

Many sizes of spherical roller bearings are supplied in X-life design. These bearings do not have a central rib on the inner ring so longer barrel rollers can be fitted; improved kinematics, optimised surfaces and even higher performance materials are possible. As a result, the bearings show a significant increase in the basic dynamic load rating and, under the same operating conditions, in the basic rating life. In certain applications, a smaller design of bearing arrangement can therefore be used if necessary.

Approx. Rs 14,000 / Piece(s)Get Latest Price

Sealing rings are designed as contact seals. They protect the bearing position against contaminants, spray water and excessive loss of grease.

The sealing rings are matched to the small radial dimensions of drawn cup needle roller bearings and needle roller bearings. They are very easy to fit, since they are simply pressed into the housing bore.

Sealing rings allow circumferential speeds at the seal lip of up to 10 m/s, dependent on the surface quality of the shaft.

Product Price :Get Latest Price

Available with us is a precisely engineered Ball Screws that are extensively used in various industries such as engineering and automobile. Efficient in converting of rotational motion to linear, these products are designed to meet the variegated demands of the customers. Owing to their excellent performance, longer functional life and superior quality, these products are highly demanded by the customers.

Further, these screws boasts following components:

• Screw
• Thrust Bearing
• Nut 

Approx. Rs 5,500 / Piece(s)Get Latest Price

Crossed roller bearings are bearings for precision applications that correspond in their dimensions to ISO dimension series 18 in accordance with DIN 616. They comprise outer rings, inner rings, rolling elements and plastic spacers. The outer ring is split and is held together by three retaining rings.

Due to the X arrangement of the rolling elements, these bearings can support axial forces from both directions as well as radial forces, tilting moment loads and any combination of loads with a single bearing position. This allows designs with two bearing positions to be reduced to a single bearing position. Crossed roller bearings are very rigid, have high running accuracy and are supplied with normal clearance, little clearance or preload. The bearing outer rings can be easily located in the adjacent construction by means of clamping rings.

Approx. Rs 150 / PieceGet Latest Price

Deep groove ball bearings are versatile, self-retaining bearings with solid outer rings, inner rings and ball and cage assemblies. These products are of simple design, durable in operation and easy to maintain; they are available in single and double row designs and and in open and sealed variants. Due to the production technology used, open bearings can still have turned recesses on the outer ring for seals or shields.

Due to their low frictional torque, they are suitable for high speeds.

Approx. Rs 2,000 / Piece(s)Get Latest Price

Double row angular contact ball bearings are units with solid inner and outer rings and ball and cage assemblies with polyamide, sheet steel or brass cages. They correspond in design to single row angular contact ball bearings in pairs in an O arrangement but give a narrower design than these. They differ in the size of their contact angle and the design of the bearing rings.

The bearings are available in open and sealed versions. Due to the production technology used, open bearings can still have turned recesses on the outer ring for seals or shields. Sealed bearings are maintenance-free and, as a result, allow particularly economical bearing arrangements. The self-alignment capacity of angular contact ball bearings is very small.

Approx. Rs 25 / PieceGet Latest Price

We´ve slimmed the ball down. What is the streamlined ball roller capable of?

This innovation is based on a simple “slimming plan”, which consists of just removing all areas of the ball not under load. 15 % is cut off on both sides of the ball, producing a “flattened” ball that is, of course, now 30 % narrower. This produces a new rolling element with new technical characteristics and advantages in completely new dimensions.

We’ve developed these advantages in four different directions matched to applications, while always keeping the requirements of our customers in mind.

You require more energy efficiency and improved performance?
You’re thinking of downsizing?
You place your trust in the INA brand?
You should take a closer look at our four new bearing series.

Approx. Rs 750 / PieceGet Latest Price

Series BXRO:

• Increase in performance compared with series 32 ball bearing because of up to 50 % more rolling elements
• Increased rating life

Improved Performance and Higher Bearing Accuracy: Competition for Bearings with Split Inner Rings

Ball roller bearings series BXRO are double row bearings whose rows of rolling elements are in an O arrangement. They can thus support both radial and axial forces.

In comparison to series 32 ball bearings, up to 50% more rolling elements can be fitted in these ball roller bearings due to the innovative assembly method, which enables higher basic load ratings in the same space.

The advantages of the BXRO compared with the 33 series (three ring bearings) lie in the simplified assembly as well as the increased bearing accuracy due to the optimized raceway geometry and the single-piece inner ring.

Approx. Rs 200 / Piece(s)Get Latest Price

Series BXRT:

• Less space required
• Lower friction
• Alternative to tapered roller bearings

The Tandem Design: A Low-Friction
Alternative to Tapered Roller Bearings

The tandem design of the INA ball roller bearing is a double-row bearing whose ball roller rows are in a tandem arrangement. The rolling elements can be guided using one or two cages.

Our two cage design enables us to set both raceways independently of each other to perfectly match your application. This ensures maximum load support with minimum size and lower friction.

Substituting the line contact with two point contacts lowers the friction by around 30 % in comparison with tapered roller bearings. This means that the energy consumption can be significantly reduced.

Approx. Rs 250 / Piece(s)Get Latest Price

Single row cylindrical roller bearings with cage are units comprising solid inner and outer rings together with cylindrical roller and cage assemblies. The outer rings have rigid ribs on both sides or are without ribs, the inner rings have one or two rigid ribs or are designed without ribs. The cage prevents the cylindrical rollers coming into contact with each other during rolling.

The cylindrical roller bearings are very rigid, can support high radial loads and, due to the cage, are suitable for higher speeds than the full complement designs. Bearings with suffix E have a larger roller set and are thus designed for extremely high load carrying capacity.

The bearings can be taken apart and can therefore be fitted and dismantled more easily. Both bearing rings can therefore have an interference fit.

Single row cylindrical roller bearings with cage are available as non-locating, semi-locating and locating bearings.

X-life

Many sizes are supplied in X-life design.
Bearings of X-life quality have a lower roughness Ra and superior geometrical accuracy of the raceways than comparable designs that are not X-life. As a result, the load carrying capacity and life of these bearings is higher while maintaining the same dimensions. In certain applications, a smaller design of bearing arrangement can therefore be used if necessary.

Approx. Rs 1,500 / Piece(s)Get Latest Price

X-life

Many sizes are supplied in X-life design. These bearings are indicated in the dimension tables.
Bearings of X-life quality have a lower roughness Ra and superior geometrical accuracy of the raceways than comparable designs that are not X-life. As a result, the load carrying capacity and life of these bearings is higher while maintaining the same dimensions. In certain applications, a smaller design of bearing arrangement can therefore be used if necessary.

Approx. Rs 500 / Piece(s)Get Latest Price

Cylindrical roller bearings with snap ring grooves are full complement, self-retaining units comprising solid inner and outer rings, rib-guided cylindrical rollers and sealing rings.

The outer rings have grooves for retaining rings. The inner rings are axially split, 1 mm wider than the outer rings and are held together by a steel strip that is rolled into place.

Locating bearings

Cylindrical roller bearings with snap ring grooves are locating bearings. These bearings are highly rigid and can support axial forces in both directions as well as high radial forces.

Due to the full complement design of these bearings, they have the largest possible number of rolling elements and thus extremely high basic dynamic and static load ratings. Due to their kinematic conditions, however, they cannot achieve the high speeds that are possible when using cylindrical roller bearings with cage.

Bearings for cable sheaves

Due to the grooves in the outer ring, the bearing rings can be axially located with ease. The bearings are therefore very suitable in bearing arrangements for cable sheaves.

Approx. Rs 2,000 / Piece(s)Get Latest Price

Full complement cylindrical roller bearings have solid inner and outer rings and rib-guided cylindrical rollers. Since these bearings have the largest possible number of rolling elements, they have extremely high radial load carrying capacity, high rigidity and are suitable for particularly compact designs. Due to their kinematic conditions, however, they cannot achieve the high speeds that are possible when using cylindrical roller bearings with cage.

Full complement cylindrical roller bearings are available as non-locating, semi-locating and locating bearings and in single and double row designs.

X-life

Many sizes are supplied in X-life design. These bearings are indicated in the dimension tables.
Bearings of X-life quality have a lower roughness Ra and superior geometrical accuracy of the raceways than comparable designs that are not X-life. As a result, the load carrying capacity and life of these bearings is higher while maintaining the same dimensions. In certain applications, a smaller design of bearing arrangement can therefore be used if necessary.

Approx. Rs 4,000 / PieceGet Latest Price

Cylindrical roller bearings of this type are double row precision bearings for machine tools. They allow radially rigid, high precision bearing arrangements and are mainly used for the radial support of main spindles.

The bearings comprise solid outer rings without ribs, solid inner rings with three ribs and cylindrical roller and cage assemblies with solid brass cages. For optimum setting of the radial internal clearance, the inner ring has a tapered bore with a taper of 1:12. The cylindrical roller bearings can be dismantled and are therefore easier to fit and remove. Both bearing rings can therefore have an interference fit.

Approx. Rs 500 / Piece(s)Get Latest Price

Barrel roller bearings are single row, self-aligning roller bearings. They comprise solid outer rings with a concave raceway, solid inner rings with two ribs and a cylindrical or tapered bore and barrel rollers with cages. The bearings cannot be dismantled.

Barrel roller bearings are particularly suitable where high radial shock type loads occur and misalignments must be compensated, see Compensation of angular misalignments. Their axial load carrying capacity is small.

Approx. Rs 250 / PieceGet Latest Price

Drawn cup needle roller bearings with open ends and with closed end are units comprising thin-walled drawn outer rings and needle roller and cage assemblies. Drawn cup need roller bearings with open ends are also available in full complement versions. The majority of the bearings are single row designs.

Drawn cup needle roller bearings with open ends and with closed end are available in open and sealed versions. Due to the thin-walled outer drawn cup and the absence of an inner ring, drawn cup needle roller bearings with open ends and with close end have an extremely low radial section height. They have very high load carrying capacity, are suitable for high speeds and can be easily fitted. If shoulders, snap rings etc. are not used for axial location, the housing bore can be produced easily and particularly economically.

Approx. Rs 200 / Piece(s)Get Latest Price

Needle roller bearings are single or double row units comprising machined outer rings with ribs, needle roller and cage assemblies and removable inner rings. The bearings are available in open and sealed versions.

X-life

Needle roller bearings with ribs are X-life bearings. In these bearings, the roughness and geometrical accuracy of the raceways have been optimised. This gives higher load carrying capacity and longer life.

Approx. Rs 250 / Piece(s)Get Latest Price

Needle roller bearings without ribs are single or double row units comprising machined outer rings without ribs, needle roller and cage assemblies and removable inner rings.

The bearings are not self-retaining. This means that the outer ring, needle roller and cage assembly and inner ring can be fitted independently of each other.

X-life

Needle roller bearings without ribs are X-life bearings. In these bearings, the roughness and geometrical accuracy of the raceways have been optimised. This gives higher load carrying capacity and longer life.

Approx. Rs 200 / Piece(s)Get Latest Price

Aligning needle roller bearings are units comprising drawn outer cups, plastic support rings with a concave inner profile, outer rings with a spherical outside surface, needle roller and cage assemblies and removable inner rings.

The bearings can compensate static shaft misalignments and can thus tolerate misalignment of the shaft relative to the housing.

Aligning needle roller bearings are firmly seated in the housing bore. The bore can therefore be produced easily and economically.

X-life

Aligning needle roller bearings are X-life bearings. In these bearings, the roughness and geometrical accuracy of the raceways have been optimised. This gives higher load carrying capacity and longer life.

Approx. Rs 200 / PieceGet Latest Price

Combined needle roller bearings are units comprising radial needle roller bearings with a rolling bearing component capable of supporting axial loads.

X-life

Combined needle roller bearings are X-life bearings. In these bearings, the roughness and geometrical accuracy of the raceways have been optimised. This gives higher load carrying capacity and longer life.

Approx. Rs 500 / PieceGet Latest Price

Axial deep groove ball bearings comprise shaft locating washers, housing locating washers and ball and cage assemblies. The bearings are not self-retaining; the ball and cage assembly and bearing washers can therefore be fitted independently of each other.

In addition to series with flat washers, there are also series with spherical housing locating washers for compensation of static misalignment. These designs are normally used in comjunction with support washers. Axial deep groove ball bearings are available in single and double direction designs.

Both designs can support high axial forces but must not be subjected to radial loads.

Approx. Rs 2,000 / Piece(s)Get Latest Price

Axial cylindrical roller bearings

Axial cylindrical roller bearings comprise axial cylindrical roller and cage assemblies and shaft and housing locating washers.
The bearings have particularly small axial section height, have high load carrying capacity and high rigidity and can support axial forces in one direction.

Axial cylindrical roller and cage assemblies

Axial cylindrical roller and cage assemblies comprise axial cages with one or two rows of cylindrical rollers. The cage assemblies have particularly small axial section height, high load carrying capacity and high rigidity. They can support axial force from one direction and act as non-locating bearings in a radial direction. Axial cage assemblies are combined with housing or shaft locating washers or are integrated directly in the adjacent construction. If they are used without axial bearing washers, the raceway must be produced as a rolling bearing raceway.

Housing locating washers

Housing locating washers are produced by machining, the outside surface is ground and the running surface is high precision machined. They are housing located and are combined with axial cage assemblies if the adjacent surface cannot be used as a raceway.

Shaft locating washers

Shaft locating washers are produced by machining, the bore is ground and the running surface is high precision machined. They are shaft located and are combined with axial cage assemblies if the adjacent surface cannot be used as a raceway.

Bearing washers

Bearing washers can be used as housing and shaft locating washers. The bore and outside surface are turned, the running surface is ground.

Approx. Rs 450 / Piece(s)Get Latest Price

Axial needle roller and cage assemblies

Axial needle roller and cage assemblies comprise plastic or metal axial cages with integrated needle rollers and have a very small axial section height. They can support high axial forces in one direction. Radial loads must be supported by separate means. Axial needle roller and cage assemblies require hardened and ground axial running surfaces for use as raceways.

Axial bearing washers

Axial bearing washers are punched, through hardened and polished and can be used as shaft or housing locating washers. These washers are suitable if the adjacent machine part is unhardened but is sufficiently rigid and geometrically accurate.

Axial needle roller bearings

Axial needle roller bearings are units comprising axial needle roller and cage assemblies and axial bearing washers with a centring spigot. They can be combined with drawn cup needle roller bearings and needle roller bearings. The axial running surface for the needle roller and cage assembly must be hardened and ground.

Approx. Rs 750 / Piece(s)Get Latest Price

Yoke type track rollers

Yoke type track rollers are single or double row units fitted on studs. They comprise thick-walled outer rings with a profiled outside surface and needle roller and cage assemblies or full complement sets of cylindrical or needle rollers. Yoke type track rollers can support high radial loads and axial loads arising from misalignments and skewed running and are suitable for cam drives, slideways, conveying equipment etc. The bearings are available with or without an inner ring as well as in open and sealed versions.

Stud type track rollers

Stud type track rollers comprise thick-walled outer rings with a profiled outside surface, solid roller studs with a locating thread, thrust washers and needel roller and cage assemblies or single or double row full complement sets of cylindrical or needle rollers. They can support high radial loads and axial loads arising from misalignments and skewed running and are suitable for cam drives, slideways, conveying equipment etc. The bearings are available in several designs and with or without an eccentric.

Approx. Rs 200 / Piece(s)Get Latest Price

Bearing arrangements for screw drives are subject to requirements that often cannot be optimally fulfilled by conventional bearings due to their design construction. For the design of maintenance-free or low-maintenance bearing arrangements for the highly dynamic operating conditions of screw drives that are precise, have high load carrying capacity, high rigidity and low friction and are easy to fit, INA/FAG maintains a wide range of axial angular contact ball bearings. With this highly developed product range, the best application-specific solution can be found for all the technical and economic requirements placed on screw drive bearing arrangements.

Multi-row designs

Axial angular contact ball bearings are available in single row, double row or triple row ready-to-fit units. They are self-retaining and comprise thick-walled, geometrically stable outer rings, ball and cage assemblies and single-piece or two-piece inner rings. In several series, the outer ring has through holes for straightforward flange mounting of the bearing to the adjacent construction. The bearing rings are matched to each other such that a defined preload is achieved once the rings are clamped by means of a precision locknut.

Approx. Rs 2,500 / PieceGet Latest Price

Approx. Rs 2,500 / Piece(s)Get Latest Price

Spindle bearings are single row angular contact ball bearings comprising solid inner and outer rings and ball and cage assemblies with solid window cages. They cannot be dismantled. The bearings are available in open and sealed versions.

Spindle bearings have restricted tolerances. They are particularly suitable for bearing arrangements with very high requirements for guidance accuracy and speed capacity. They have proved highly suitable for the bearing arrangements of spindles in machine tools.

Approx. Rs 700 / Piece(s)Get Latest Price

Inner rings are made from hardened rolling bearing steel and have precision machined or ground raceways.

They are used where:

• the shaft cannot be used as a raceway with needle roller and cage assemblies, drawn cup needle roller bearings with open ends, drawn cup needle roller bearings with closed end and needle roller bearings
• needle roller bearings must be combined with wider inner rings in order to facilitate axial displacement of the shaft in relation to the housing
• optimum running surfaces are required for the seal lips.

Inner rings, precision machined

In inner rings IR, the raceway is precision machined. Chamfers on the end faces allow easy insertion into the bearings and prevent damage to the seal lips of the bearings. The inner rings are available with and without a lubrication hole.

Inner rings, ground

In inner rings LR, the raceway is ground. The end faces are turned and the edges are broken. These rings have larger tolerances than the rings of series IR. They are therefore suitable for applications that permit larger tolerances for width and less demanding requirements for axial runout.

Approx. Rs 17,000 / Piece(s)Get Latest Price

INA slewing rings are known worldwide as premium products in the field of rolling bearing technology. These machine elements have proved themselves many times over, have high load carrying capacity, a versatile range of applications and are highly cost-effective. Due to their design, a single bearing can reliably support radial, axial and tilting moment loads. It is therefore possible in many cases to replace bearing arrangements comprising a combination of radial and axial bearings by a single bearing. This reduces, in some cases considerably, the costs and work required in the design of the adjacent construction and the fitting of bearings.

Slewing rings are sealed on both sides, lubricated with a high quality grease, can be relubricated via lubrication nipples and are particularly easy to fit. The bearing rings are supplied without gear teeth or, in order to achieve simple drive solutions, are available with external or internal gear teeth.

Approx. Rs 150 / Piece(s)Get Latest Price